Installation & setup

Setting up your neon

Everything you need to choose, hang and enjoy your sign, from what comes in the box to the first switch-on.

Banana neon sign glowing white and yellow on a dark wall, held off the wall by silver standoffs

Before you buy

Good to know before you order

Where it can go

Our standard signs are made for indoors, or for outdoor spots that are fully covered and protected from the weather.

Planning an outdoor sign? Add the waterproofing option when you order, and talk to us about your spot so we can help you plan the power setup.

Power

Your sign plugs into a normal wall socket through its own power adapter, so choose a spot within reach of a socket.

Not sure the cable will reach? Ask us before you order.

Hanging it

Every sign comes ready to wall-mount, with the hardware included. Once it's up, it floats about 20 mm off the wall.

Hanging a sign is a two-person job, so plan to have a helper on the day.

See display options

Choosing a colour setup

Single colour: one colour, with a dimmer and remote.

Multicolour: several fixed colours built into the design. The colours stay as designed and don't change.

RGB colour-changing: switch colours and effects with a colour-wheel remote.

What's in the box

The real kit, laid out

These are photos of the actual kits that come with our signs. Choose your sign type to see what's included.

Single-colour neon sign kit laid out: power adapter, power cable, wall plugs, standoffs, remote and dimmer
  • Your sign, on its clear acrylic backing
  • Power adapter and cables
  • Dimmer, which sits between the sign and the adapter
  • Dimmer remote
  • Mounting kit (see below)

The mounting kit

Our standard kit mounts the sign at four points, and includes:

  • 4 metal spacers
  • 4 wall screws
  • 4 wall plugs
  • 4 front fixings (the cap screws you see on the front)
  • 8 silicone washers, two per spacer

If your sign has a different number of mounting holes, it comes with hardware to match.

Installation

Wall-mounting, step by step

No experience needed. Clear some space below the wall, take your time, and work through the steps in order.

You'll need a helping hand!

Hanging a neon sign is a two-person job. One of you holds the sign steady while the other marks the holes, and again while the front fixings go in. Line up a helper before you start.

In the box

  • Your sign on its acrylic backing
  • Mounting kit: spacers, wall screws, wall plugs, front fixings and silicone washers
  • Power adapter and cables
  • Dimmer or controller, and remote (where supplied)

You'll need

  • A second person
  • Pencil
  • Measuring tape
  • Spirit level or a level app
  • Drill, with a bit that suits your wall plugs and wall
  • Screwdriver or driver bit
  • Different wall fixings, if the supplied plugs don't suit your wall
  1. Person crouching beside a lit neon sign propped against a white wall
    1

    Unpack, check and test

    Unpack your sign and check you have everything in the kit list.

    Before anything goes on the wall, connect the sign to its power and switch it on for a quick test. Then unplug it before you carry on.

    Testing first means you'll never find a problem after the sign is already up.

  2. Orange neon sign on a timber-lined wall between a door and a window
    2

    Choose your spot

    • How high do you want it, and where will it look best?
    • How will the cable reach the nearest socket?
    • Is the wall solid enough to hold the sign?
    • Is there room around it to drill and fit the hardware?

    Once it's up, the sign sits about 20 mm off the wall.

    Before you drill anywhere: check the wall for hidden electrical cables and pipes.

  3. Person holding green, pink and yellow neon figures against a wall to line them up
    3 Two-person step

    Position, level and mark

    Lift the sign into place together. One person holds it firmly against the wall while the other checks it's level and that the cable will reach the socket.

    Keep the sign completely still. With a pencil, mark the wall through the exact centre of every mounting hole in the clear backing.

    Take your time here!

    Make sure each pencil mark is exactly centred in its hole. Accurate marks mean your spacers line up perfectly when it's time to hang the sign. If a mark is even slightly off, the front fixings will have to go in at an angle.

    Later on, never force the sign or the fixings into line. If they don't meet easily, re-check the spacers.

    Left: pencil mark in the exact centre of the hole, correct. Right: pencil mark off to one side, wrong. ✓ Centred ✗ Off-centre
    Double-check every mark before you take the sign down.
  4. Hand holding four silver standoffs and white wall plugs with screws for mounting a neon sign
    4

    Drill and plug the holes

    Put the sign down somewhere safe and check your marks one more time. Then drill a hole at each mark and push a wall plug into each one so it sits flush with the wall.

    Our installation sheet uses a 9 mm (0.9 cm) drill bit for the supplied wall plugs. Walls vary, though. Plasterboard, brick, concrete and timber can each need a different bit and fixing, so always use ones that suit your wall. If you're unsure, ask a hardware store or a handyperson.

  5. Close-up of a silver standoff held between two fingers, with more mounting hardware behind
    5

    Fix the spacers to the wall

    Push a wall screw through the middle of a metal spacer and screw it into the plug, so the spacer sits firmly against the wall. Repeat for each hole.

    When they're all on, the spacers should match the holes in the backing exactly. If one looks out of line, sort it out now before you hang the sign.

  6. Hand turning a front fixing on a glowing neon sign, with the metal spacer visible behind the clear backing
    6 Two-person step

    Hang the sign and fit the front fixings

    Washers first. Each mounting point uses two silicone washers, one behind the acrylic and one in front. They cushion the acrylic so metal never presses straight onto it.

    1. Place one washer over the end of each spacer, so it will sit between the spacer and the back of the acrylic.
    2. Together, lift the sign so each hole lines up with its spacer. The holes should line up on their own. If they don't, stop and check rather than forcing it.
    3. While your helper holds the sign, slide the second washer onto a front fixing, push it through the hole and turn it by hand into the spacer.
    4. Start all the fixings by hand first, then tighten them evenly until the sign is held firmly. Snug is enough, so don't over-tighten against the acrylic.
    Side view of one mounting point, from the wall outwards: wall plug and wall screw, metal spacer about 20 millimetres long, silicone washer, clear acrylic backing, second silicone washer, front fixing. Wall about 20 mm Metal spacer Plug Washer (behind) Washer (in front) Acrylic backing Front fixing
    Each mounting point, from the wall outwards.
  7. Connection order: sign, then dimmer or controller where supplied, then power adapter, then wall socket Sign Dimmer /controller Adapter Socket 1234, last if supplied
    7

    Connect the power

    With the socket switched off, connect the sign to its dimmer or controller (if your sign came with one), then to the power adapter. Plug into the wall last.

    Setups vary between signs, so follow the connectors supplied with yours.

    Only use the power adapter supplied with your sign.

  8. Hand holding a dimmer remote below a glowing neon sign
    8

    Switch on and enjoy the glow!

    Turn on the socket and bring your sign to life. Use the remote to set the brightness, or on RGB signs to pick a colour or effect.

    Then step back and enjoy it. You did that!

    How the remotes work · Connect an RGB remote

Side view of a mounted neon sign: the metal spacer against the wall, the clear acrylic backing and the front fixing Close-up of a metal spacer and front fixing holding a glowing neon sign off the wall
All done: the spacers hold the sign about 20 mm off the wall, so it seems to float.

Display options

Choose how to display it

Close-up of a neon sign fixed to the wall with a metal spacer

Wall-mounted Standard

Our standard method, with the hardware included. The sign floats about 20 mm off the wall. See the steps

Person sitting on a wooden floor beside a neon sign leaning against the wall

Shelf or leaning

Stand it upright on a sturdy, stable surface, or lean it securely against a wall. Make sure it can't slide, tip over or be knocked down, especially if you have little ones or pets at home.

Something else in mind?

If you'd like to display your sign another way, such as hanging it from the ceiling or on a stand, get in touch before you order and we'll tell you what's possible for your sign.

Please don't use adhesive strips or hooks unless we've confirmed they're right for your sign.

Ask us about your sign

Remotes & controls

Getting to know your remote

Which remote you get depends on your sign. Here are the two you're most likely to find in the box.

Hand holding a white dimmer remote with on, off, brightness and timer buttons

Single-colour dimmer remote

  • The green and red buttons switch the sign on and off
  • Number buttons jump straight to a brightness level
  • Mode and speed buttons change effects
  • Time buttons set a timer
Hand holding a white RGB remote with a colour wheel for changing a neon sign's colour

RGB colour-wheel remote

  • I and O switch the sign on and off
  • Touch the colour wheel to choose a colour
  • B + / − changes brightness
  • S + / − changes speed
  • M + / − changes mode

First time? Connect your RGB remote

Hand holding the small white RGB controller that sits between the sign and its power adapter

The controller

RGB signs come with this small controller. It connects between the sign and the power adapter and takes its instructions from the remote. Keep it somewhere tidy and dry, close to the sign.

RGB remote with two buttons circled in green: the I button at the top left and the bottom button under M at the lower right

RGB signs

Connect your RGB remote

Before your remote can control an RGB sign, the two need to be connected. It only takes a moment, but timing matters.

  1. Check the remote has batteries in it.
  2. Connect your sign to power and switch it on at the wall.
  3. Within 5 seconds, press and hold the two buttons circled in the photo: the I button at the top left, and the bottom button under M at the lower right.
  4. Watch the sign flash a few times. When it stops flashing and stays on, let go.
  5. You're connected! The remote now has full control of your sign.

Missed the 5 seconds? Switch off at the wall, wait a moment, and try again.

Care & help

Keeping it glowing

Care

  • Switch off before cleaning, then dust with a soft, dry cloth
  • Keep standard signs dry and out of the weather
  • Don't cover the sign while it's on
  • Only use the adapter supplied with your sign

If something's not right

The sign won't turn on

Check every connection is pushed fully together and the socket is switched on, then press the remote's on button.

The remote isn't working

Move closer to the sign and its controller and try again, and check the remote's batteries. On an RGB sign, the remote may need connecting first, so follow Connect your RGB remote.

The fixings won't line up

Don't force them. Take the sign down and check that each spacer sits exactly where its hole is. A spacer that's slightly off-centre is the usual cause.

Part of the sign is dark or flickering

Switch off at the wall and contact us. A short video or photo helps us sort it quickly.